Qolsys QZ2141-840 - IQ Smart Dimmer Z-Wave Plus V2 Plug-in Module - Alarm Grid

The Qolsys IQ Smart Dimmer plugs into a standard outlet and turns most plug-in devices into smart devices. It works with incandescent and most dimmable fluorescent (CFL) and LED lights. It is smaller than its predecessor so that it does not block the second outlet in a plug. In addition, it also serves as a Z-Wave repeater. Buy the Qolsys IQ Dimmer from Alarm Grid today!.
The Qolsys IQ Smart Dimmer plugs into a standard outlet and turns nearly any plug-in device into a smart device. It works with incandescent and most dimmable fluorescent (CFL) and LED lights. It is redesigned to be smaller than its predecessor with a more discreet appearance so that it does not block the second outlet. In addition, it also serves as a Z-Wave repeater for other nearby Z-Wave devices. There are some devices that you should not use with the Qolsys IQ Dimmer. Motor-operated appliances, non-dimmable fluorescent lighting fixtures, and transformer-powered appliances are not compatible. Also, the Qolsys QZ2141-840 does not support devices that require a ground prong receptacle. In addition, any lighting device that is connected to this module must not exceed 2.5A at 300W if incandescent, 65W if dimmable CFL or LED, 120 Volts AC at 60 Hz. It is always recommended to first exclude any Z-Wave device from the network before attempting to include it. Devices are often tested at the factory without being set back to factory default afterward. Although the IQ Dimmer is manufactured by Qolsys, it should work with any Z-Wave controller that supports Z-Wave, Z-Wave Plus, or Z-Wave Plus V2. Just keep in mind that mixing Z-Wave and Z-Wave Plus devices on the same network may introduce some limitations that the IQ Dimmer might not otherwise have. As a Z-Wave Plus V2 device, the IQ Dimmer supports S2 security and SmartStart. The QR Code for SmartStart can be found on both the box and the device itself. SmartStart allows the user to begin the inclusion process at the panel by scanning each device's QR Code using the SmartStart menu option and the panel camera. After scanning all codes and then exiting panel programming, install each device in its intended location. From there, the device and the panel will communicate with one another and complete the inclusion process. Once all devices have been included and properly configured, it's a good idea to perform a network rediscovery. This allows the controller to find the optimum route for each device. The process for manually including and excluding the Qolsys IQ Dimmer is simple. Plug the dimmer into an outlet. Put the Z-Wave controller into its exclusion mode. Press and release the button on the top of the IQ Dimmer. A message should be displayed on the controller letting you know that a device has been excluded. Then, put the Z-Wave controller into its inclusion mode. Perform the same process of pressing and releasing the button on the top of the dimmer. The controller should let you know that a new device has been detected. Complete the process of adding the device based on the Z-Wave controller being used. Specifications: Lighting Supported: Incandescent and most Dimmable Fluorescent (CFL) or LED Lights Z-Wave Protocol: Z-Wave Plus 700 Series with S2 Security and SmartStart Indicators: LED to indicate On/Off Status Electrical Limits: Light Fixtures Up To 300W (Incandescent) and 65W (Dimmable CFL/LED) Electrical Configuration: Grounded 3-Pin Plug with Safety Tab to secure IQ Dimmer to the Outlet Form Factor: Smaller than previous models, will not block the second outlet Indoor/Outdoor: Indoor Use Only Operating Ambient Temperature: 32°F - 104°F (0°C - 40°C)

How to enroll a Qolsys IQ Z-Wave Outlet into an IQ Panel 2

Qolsys IQ Panel 4: Program a Z Wave Device

How to enroll a Qolsys IQ Z-Wave Outlet into an IQ Panel 2

Home Automation Modules - Alarm Grid

Description Qolsys QR0051-840 Power Supply: The Qolsys QR0051-840 is a replacement 7-Volt DC power supply transformer designed for the IQ Panel 2 and IQ Panel 2 Plus (Rev E or higher). The IQ Power Supply QR0029-840 includes 6' wire with barrel connector for easy installation. The QR0051-840 has a higher output of 7V, than the other model number QR0029-840 transformer which only has an output of 5.5V.

Qolsys AC Adapter

Qolsys IQ Panel 4: Program a Z Wave Device

Adding a Z-Wave Device to the Qolsys IQ Panel 2

IQ DIMMER – QOLSYS

AV Power Outlets and Receptacles for Enhanced Networking

* Description * Specifications * PDF Documents, Qolsys QZ2130-840 Product Description:, The Qolsys QZ2130-840 IQ Outlet plugs into any standard outlet

QZ2130-840 - Qolsys Wireless Z-Wave IQ Outlet and Repeater

Qolsys IQ Dimmer (QZ2141-840) - Quick Install Guide - Alarm Grid

Compatible Hardware, Hardware Partners